热/力耦合作用下基于应力分析的冰破坏准则

根据飞机热除冰的物理过程,考虑外部空气动力和蒙皮表面加热的作用,建立了NACA 0012翼型前缘冰层应力计算模型。采用有限元方法和平面三角形单元对控制方程组进行了求解,获得了外部空气动力和蒙皮表面加热对冰层黏附界面应力的影响规律。研究表明:蒙皮表面不加热时,来流速度影响了黏附界面应力的强度,来流攻角影响了黏附界面应力的分布,冰-蒙皮间黏附界面切应力最大值随来流速度呈近似线性增大趋势,但外部空气动力很难造成冰层破坏。蒙皮表面加热时,冰-蒙皮间黏附界面的耦合应力和冰层内部的主应力随着热流密度的增大而增大,很容易超过剪切强度,这是造成冰破坏的关键因素。耦合冰-蒙皮剪切强度随界面温度的变化关系,初步建立了基于应力分析和热/力耦合作用的冰破坏判断准则。外部空气动力产生的界面应力和蒙皮表面加热产生的界面热应力之和，必须大于与蒙皮表面温度相关的剪切强度，则冰层发生破坏，破坏位置是耦合应力超过剪切强度的区域。      

A CFD-based numerical virtual flight simulator and its application in control law design of a maneuverable missile model

A CFD-based Numerical Virtual Flight (NVF) simulator is presented, which integrates an unsteady flow solver on moving hybrid grids, a Rigid-Body Dynamics (RBD) solver and a module of the Flight Control System (FCS). A technique of dynamic hybrid grids is developed to control the active control surfaces with body morphing, with a technique of parallel unstructured dynamic overlapping grids generating proper moving grids over the deflecting control surfaces (e.g. the afterbody rudders of a missile). For the flow/kinematic coupled problems, the 6 Degree-Of-Freedom (DOF) equations are solved by an explicit or implicit method coupled with the URANS CFD solver. The module of the control law is explicitly coupled into the NVF simulator and then improved by the simulation of the pitching maneuver process of a maneuverable missile model. A nonlinear dynamic inversion method is then implemented to design the control law for the pitching process of the maneuverable missile model. Simulations and analysis of the pitching maneuver process are carried out by the NVF simulator to improve the flight control law. Higher control response performance is obtained by adjusting the gain factors and adding an integrator into the control loop.     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。     

A novel control method for turboshaft engine with variable rotor speed based on the Ngdot estimator through LQG/LTR and rotor predicted torque feedforward

In order to compensate for the disturbance of wide variation in rotor demanded torque on power turbine speed and realize the fast response control of turboshaft engine during variable rotor speed, a cascade PID control method based on the acceleration estimator of gas turbine speed (Ngdot) and rotor predicted torque feedforward is proposed. Firstly, a two-speed Dual Clutch Transmission (DCT) model is applied in the integrated rotor/turboshaft engine system to achieve variable rotor speed. Then, an online estimation method of Ngdot based on the Linear Quadratic Gaussian with Loop Transfer Recovery (LQG/LTR) is proposed for power turbine speed cascade control. Finally, according to the cascade PID controller based on Ngdot estimator, a rotor demanded torque predicted method based on the Min-batch Gradient Descent-Neural Network (MGD-NN) is put forward to compromise the influence of rotor torque interference. The simulation results show that compared with cascade PID controller based on Ngdot estimator and the one combined with collective pitch feedforward control, the novel control method proposed can reduce the overshoot of power turbine speed by more than 20%, which possesses faster response, superior dynamic effect and satisfactory robustness performance. The control method proposed can realize the fast response control of turboshaft engine with variable rotor speed better.     

天基强银河背景下的空间碎片探测试验及分析

本文设计并完成了银河背景下碎片探测试验，数据分析表明，强的银河背景会降低探测器对暗弱碎片的探测能力，但对碎片的天文定位精度影响不大。本文验证了采用基于探测概率的极限探测星等方法表征探测器极限探测能力的合理性，以及基于仿真的方法增加数据完备度的可行性。本文的工作将为后续天基探测器的设计及探测试验的开展提供依据。     

Numerical investigation of flow mechanisms of tandem impeller inside a centrifugal compressor

This study numerically investigated a single stage centrifugal compressor ‘‘Radiver’’ with a wedge diffuser and several tandem-designed impellers to explore the flow phenomena within the tandem impeller and the potential to enhance compressor performance. The results demonstrate that tandem design and clocking fraction (λ_s) significantly affects the compressor performance. The compressor stage with tandem impellers of Series A of boundary layer growth interruption alone are observed to have a widely operating range but efficiency and total pressure ratio penalty compared with that of conventional impeller. The tandem impeller with at least the same impeller efficiency as the conventional design is considered as a critical design criteria so that further modification process based on the flow characteristic of tandem impeller is necessary. In order to restrain the inducer wake and exducer shock losses, parameters modification of blade angle and thickness distributions are necessary and the modified tandem impeller of Series B is obtained. The modified tandem impeller with 25% clocking arrangement shows an 8.45% stall margin increase and maintains the total pressure ratio and efficiency as the conventional design, which proves the potential of tandem impeller to improve compressor stage performance. It is noteworthy that the tandem impellers of Radiver have not shown obviously balanced exit flow field and the fundamental mechanism of stall margin extending of tandem impeller lies on the improved impeller/diffuser matching performance resulting from the incidence angle variation at diffuser inlet.     

边界层抽吸对超燃冲压发动机流场特性的影响研究

为了解边界层抽吸对超燃冲压发动机流场的影响,采用风洞试验和数值计算对隔离段激波串特性以及燃烧室燃烧特性进行了研究。结果表明,在发动机入口马赫数2.0,总温950K,总压0.82MPa的来流条件下,当量比为0.18先锋氢气与不同当量比煤油共同燃烧呈不稳定状态,激波串在隔离段内前后振荡传播。当煤油当量比为0.29时,激波串振荡前缘远离抽吸位置,边界层抽吸对发动机流场基本没有影响。随着煤油当量比逐渐增大,激波串前缘位置到达抽吸区附近,边界层抽吸开始产生影响,改变了隔离段内的激波串动态演化过程、形态结构以及位置分布,同时有效提高了隔离段抗反压特性,使得煤油最大当量比可以由0.38增大至0.42。此外,边界层抽吸对发动机内的亚燃/超燃区域分布也会产生影响。     

Bayesian network-based extraction of lunar impact craters from optical images and DEM data

Impact craters are among the most noticeable geomorphological features on the planetary surface and yield significant information about terrain evolution and the history of the solar system. Thus, the recognition of impact craters is an important branch of modern planetary studies. Aiming at addressing problems associated with the insufficient and inaccurate detection of lunar impact craters, a decision fusion method within the Bayesian network (BN) framework is developed in this paper to handle multi-source information from both optical images and associated digital elevation model (DEM) data. First, we implement the edge-based method for efficiently searching crater candidates which are the image patches that can potentially contain impact craters. Secondly, the multi-source representations of an impact crater derived from both optical images and DEM data are proposed and constructed to quantitatively describe the two-dimensional (2D) and three-dimensional (3D) morphology, consisting of Histogram of Oriented Gradient (HOG), Histogram of Multi-scale Slope (HMS) and Histogram of Multi-scale Aspect (HMA). Finally, a BN-based framework integrates the multi-source representations of impact craters, which can provide reductant and complementary information, for distinguishing craters from non-craters. To evaluate the effectiveness and robustness of the proposed method, experiments were conducted on three lunar scenes using both orthoimages from the Lunar Reconnaissance Orbiter (LRO) and DEM data acquired by the Lunar Orbiter Laser Altimeter (LOLA). Experimental results demonstrate that integrating optical images with DEM data significantly decreases the number of false positives compared with using optical images alone, with F₁-score of 84.8% on average. Moreover, compared with other existing fusion methods, our proposed method was quite advantageous especially for the detection of small-scale craters with diameters less than 1000 m.     

C/SiC材料主被动氧化烧蚀机理及计算方法研究

基于热化学平衡方法建立了任意比例C/SiC材料的主被动氧化烧蚀模型，开展了C/SiC材料氧化烧蚀机理的计算研究，并基于典型材料烧蚀试验结果进行了充分验证。计算结果表明，C/SiC材料的氧化烧蚀特性取决于表面温度、氧分压以及组分等因素，可能会出现主动氧化和被动氧化两种破坏机制，目前的烧蚀模型能够预测出任意比例C/SiC材料两种氧化烧蚀机制的转换过程；SiC含量对C/SiC材料的氧化烧蚀特性有明显的影响，随着SiC含量的提升，主/被动氧化转换临界分压会减小，材料的抗氧化性能越好；但当材料均处于主动氧化阶段时，SiC含量越高材料的无量纲烧蚀速率越大，材料的抗烧蚀性能减弱。     

Д-30发动机ЭИ868合金扇形块的钎焊修复

针对某Д-30发动机大修对ЭИ868合金(对应于我国的牌号GH3044)扇形块的修复要求,采用真空钎焊的方法对扇形块进行了钎焊补焊。对钎焊补焊的扇形块进行超声波探伤。结果表明,钎缝内部质量满足HB7575-97一级钎焊接头的要求,表明所确定的修复工艺可实现ЭИ868合金扇形块的可靠修复。